See what's new at PRINTING UnitedNew at PRINTING UnitedBooth 3268 · Las Vegas · Sept 23–25Book a demo
ContactShop — dealer and account ordering

Seismo L16R & L24R

Seismo L16R & L24R Quick Start Guide

Every step links to its own moment in the video, so you never hunt for the right part again.

  • 16 steps
  • 67 instructions
  • 1 video
  • Updated 2026-04-16

Seismo L16R User manualSeismo L24R User manualThe full manual, beyond first setup. · All manuals

Initial Setup

Seismo L16R and Seismo L24R Initial Setup Guide

  1. 0:02Tools Required
  2. 0:10Uncrating the Machine
  3. 0:48Removing Crate Supports and Packaging
  4. 1:30Removing the Machine from the Pallet
  5. 2:20Identifying Included Components
  6. 2:59Installing Cooling Fan Brackets
  7. 3:20Installing the Cooling Fan
  8. 4:02Installing the Take-Up Bars and System
  9. 4:44Installing the Take-Up Core and Final Alignment
  10. 5:33Vacuum and Powder Tray Setup
  11. 5:45Internal Packaging Removal
  12. 6:26Final Exterior Setup
  13. 6:55Power Connection and Electrical Setup
  14. 7:17Main Breaker Activation and Power-On Test
  15. 7:40Setup Verification
Written steps16

Tools Required

Watch this part0:02

What you need

  • Allen key
  • Scissors
  • Pliers
  • Flat screwdriver
  • Phillips screwdriver

Uncrating the Machine

Watch this part0:10
  1. Use a flat screwdriver to push the metal prongs on the top of the crate upward.
  2. Use pliers to straighten the prongs upward.
  3. Lift the lid upward to open the crate.
  4. Push the lower prongs downward in reverse to release them.
  5. Repeat the same process for the side prongs.
  6. Pull the crate walls off one by one.

Removing Crate Supports and Packaging

Watch this part0:48
  1. Use a screwdriver to remove the screws on both sides of the crate.
  2. Remove the two horizontal support bars.
  3. Remove the plastic covers and set them aside for future use as dust covers.
  4. Remove all boxes and loose parts surrounding the machine.

Removing the Machine from the Pallet

Watch this part1:30
  1. Use an Allen wrench to remove the bolts securing the machine to the pallet.
  2. Prepare a minimum of four people to assist with moving the machine.
  3. Carefully slide the machine off the pallet.
  4. Gently set the machine down on the floor.
  5. Remove all external plastic shrink wrap.

Identifying Included Components

Watch this part2:20

What you need

  • Take-up system
  • Take-up brackets
  • Take-up bars
  • Cooling fan for media cooling

Installing Take-Up Brackets

  1. Remove shrink wrap from the take-up brackets.
  2. Locate the bag containing bolts and Allen key.
  3. Identify left and right brackets using the notch orientation.
  4. Attach the brackets to the machine using the provided bolts.
  5. Do not fully tighten the bolts at this time.

Installing Cooling Fan Brackets

Watch this part2:59
  1. Remove shrink wrap from the cooling fan.
  2. Locate the two cooling fan brackets inside the packaging.
  3. Install the brackets using the same bolts.
  4. Ensure correct orientation and pull brackets fully outward before securing.

Installing the Cooling Fan

Watch this part3:20
  1. Remove the pre-installed bolts from the cooling fan by hand.
  2. Position the cooling fan as shown in the video.
  3. Reinstall the two closest bolts without fully tightening.
  4. Install the remaining bolts.
  5. Once positioned correctly, tighten all bolts by hand.
  6. Install the power cable by turning it clockwise to tighten.

Installing the Take-Up Bars and System

Watch this part4:02
  1. Loosen the bolts on top of the take-up brackets using an Allen wrench.
  2. Install the first take-up bar and lightly tighten bolts by hand.
  3. Thread the second take-up bar through the take-up system.
  4. Loosen bolts as needed to pass the bar through the holes.
  5. Position the full take-up system onto the brackets.
  6. Thread the bar through both brackets.
  7. Connect the opposite side of the take-up system to the second bar.
  8. Tighten bolts by hand to secure the bars.

Installing the Take-Up Core and Final Alignment

Watch this part4:44
  1. Spread out the take-up system evenly.
  2. Install the take-up core into place.
  3. Tighten the core bolts by hand.
  4. Route the power cable on the right side as shown.
  5. Center all components.
  6. Fully tighten all bolts using the Allen key.

Vacuum and Powder Tray Setup

Watch this part5:33
  1. Locate the vacuum cleaner and accessories.
  2. Plug in the vacuum to allow it to charge.
  3. Identify the tray at the bottom used to catch excess powder.

Internal Packaging Removal

Watch this part5:45
  1. Remove remaining shrink wrap from the machine exterior.
  2. Unlock all four latches.
  3. Lift the heating elements.
  4. Remove all internal shrink wrap and foam.
  5. Lower the lid halfway and manually release the safety slot.
  6. Close the lid fully and lock all latches.

Final Exterior Setup

Watch this part6:26
  1. Remove protective film from the take-up reel.
  2. Remove protective film from the top cover.
  3. Lift the front heating plate.
  4. Use the support beam to hold the plate open.
  5. Leave the ground wire as is, or attach it to the heating plate if static issues occur.

Power Connection and Electrical Setup

Watch this part6:55
  1. Plug the power cable into an outlet.
  2. Verify power requirements: 220V, 5.2 kW, 24 amps.
  3. If required, hardwire the machine according to local standards.

Main Breaker Activation and Power-On Test

Watch this part7:17
  1. Loosen the two bolts on the main breaker panel.
  2. Open the breaker lid.
  3. Turn the breaker on.
  4. Close the lid and secure it.
  5. Power on the shaker.
  6. Verify that all systems power on correctly.

Setup Verification

Watch this part7:40

What you need

  • Machine powers on successfully
  • No error indicators present
  • All components installed securely

Stuck on a step?

Our US tech team answers on Discord, and it is the fastest route to a person who knows this machine.

Get support