Prisma Dual

Prisma Dual Quick Start Guide

Every step links to its own moment in the videos, so you never hunt for the right part again.

  • 36 steps
  • 131 instructions
  • 2 videos
  • 2 chapters
  • Updated 2026-11-15
Resources1

1. Unbox and Set Up

Prisma Dual — Unboxing & Setup

  1. 0:00Overview
  2. 0:11Tools to prepare
  3. 0:38Remove the crate side panels
  4. 1:08Raise leveling feet so the unit can roll
  5. 1:26Build a ramp and roll the machine off the crate
  6. 1:55Open side cabinets and locate accessories
  7. 2:12Lock and verify platen placement
  8. 2:34Connect the foot pedal (Accessory Box #2)
  9. 3:00Power + waste bin + laser guide plastic
  10. 3:31Optional accessories (Laser pads + Teflon cover)
  11. 4:00Power on the Prisma Dual and enable air to the system
  12. 4:22Test press function (two-button press)
Written steps20
  • Walk-through of the complete unboxing and setup process for the Prisma Dual.

Tools to prepare

Watch this part0:11
  • Adjustable wrench
  • Gloves
  • Utility knife
  • Power drill (a screwdriver also works)

Remove the top panel of the crate

  1. The Prisma Dual arrives in a wooden crate secured with metal L brackets.
  2. Remove the top panel by unscrewing the L brackets along the top edge.
  3. Repeat for all L brackets securing the top panel.
  4. Lift the top panel off.

Remove the crate side panels

Watch this part0:38
  1. Remove the screws from the L brackets securing the front panel.
  2. Remove the front panel.
  3. Repeat the same process for each remaining side panel until the machine is fully exposed.

Release the machine from the crate base

  1. Locate the metal brackets securing the machine to the base of the crate.
  2. Remove the three screws from each bracket to release the machine from the crate base.

Raise leveling feet so the unit can roll

Watch this part1:08
  1. At the base of the Prisma Dual, locate the adjustable leveling feet.
  2. Using an adjustable wrench, rotate each leveling foot clockwise to raise it off the ground.
  3. Confirm the machine can roll freely.

Remove protective cover

  • Remove the protective cover from the Prisma Dual.

Build a ramp and roll the machine off the crate

Watch this part1:26
  1. Locate the 2x4 beam under the Prisma Dual and place it vertically against the pallet.
  2. Take one of the removed crate panels and position it against the 2x4 to create a ramp.
  3. Bend the L brackets downward and secure the ramp using screws to ensure it is stable.
  4. With multiple people assisting, carefully roll the machine down the ramp.

Open side cabinets and locate accessories

Watch this part1:55
  1. Open the side cabinets.
  2. Inside are five accessory boxes, each labeled with a number.

Install the platen (Accessory Box #3)

  1. Open accessory box number three.
  2. Remove the platen.
  3. Place the platen into position until it seats fully.

Lock and verify platen placement

Watch this part2:12
  1. Push the locking lever to the side to secure the platen.
  2. Shake the platen lightly to confirm it is secured properly.
  3. Compare it to the other platen to confirm both are positioned the same.

Connect the air compressor (Accessory Box #1)

  1. Open accessory box number one to access the air compressor.
  2. Take the air tube and connect it to the compressor output.
  3. Pull back the locking ring, insert the tube until it clicks, then release the ring to lock.
  4. Connect the other end of the air tube to the machine’s air port.
  5. Push the tube in fully to ensure a secure connection.

Connect the foot pedal (Accessory Box #2)

Watch this part2:34
  1. Open accessory box number two to access the foot pedal assembly and cables.
  2. Slide the strain relief collar against the pedal assembly.
  3. Rotate the strain relief collar clockwise to secure the cable.
  4. Connect the other end of the pedal cable to the corresponding port on the machine.
  5. Tighten the locking ring clockwise.

Power + waste bin + laser guide plastic

Watch this part3:00
  1. Plug the main power cable into the Prisma Dual.
  2. Locate the waste bin and position it underneath the machine as shown.
  3. Remove the protective plastic from the laser guides.

Optional accessories (Laser pads + Teflon cover)

Watch this part3:31
  1. Open accessory box number four to access the laser guide pads.
  2. Open accessory box number five to access the Teflon cover (optional cover for platens).

Plug in and power on the air compressor

  1. Plug the Prisma Dual and the air compressor into a power outlet.
  2. On the compressor, rotate the red knob toward the airline to open airflow.
  3. Pull the red knob upward to power the compressor on.
  4. Verify the pressure gauge begins to rise.

Power on the Prisma Dual and enable air to the system

Watch this part4:00
  1. Turn the Prisma Dual power switch to the ON position.
  2. Wait for the control menu to appear.
  3. On the side, locate the air gauge and the blue air release control.
  4. Push the blue control to the right to allow air into the system.

Test platen movement (foot pedal)

  1. Press the foot pedal.
  2. Confirm the platen shifts smoothly to the opposite side.

Test press function (two-button press)

Watch this part4:22
  1. Press the press buttons on both sides simultaneously.
  2. Confirm the press function operates correctly.

Finish

  • If all tests are successful, the Prisma Dual is fully unboxed and set up.

2. Operation

How to Operate the Prisma Dual

  1. 0:18Stabilize the Press
  2. 0:47Connect Power, Air and the Foot Pedal
  3. 1:11Power On and Turn On the Air
  4. 1:39Set the Temperature
  5. 1:53Set the Press Times
  6. 2:57Run a Double Press
  7. 3:57Triple Press
  8. 4:35Set the Pressure
  9. 5:38Press Counter
  10. 6:03Read the Status
  11. 6:39Save Presets
  12. 7:42Advanced Settings
  13. 8:51Manual Mode
  14. 9:41Semi-Auto Mode
  15. 10:57Auto Mode
  16. 12:37Tips
Written steps16

Stabilize the Press

Watch this part0:18
  1. Find the stabilizer legs. There is one next to each wheel.
  2. Twist each leg clockwise to lower it to the floor. Do the same at every wheel.
  3. Make sure the machine is stable.
  4. The storage compartment is in the base. Turn the handle to open the door, take out any supplies you need, then close the door and turn the handle.

Connect Power, Air and the Foot Pedal

Watch this part0:47
  1. Plug the power cable into the socket on the back of the press.
  2. Connect the air line from your compressor to the air port.
  3. The foot pedal cable goes into the round port. The plug only fits one way: line up its slot with the port.
  4. Push the plug in, then turn the ring by hand to tighten it.

Power On and Turn On the Air

Watch this part1:11
  1. Press the power switch to turn on the Prisma Dual.
  2. On top of the air compressor, release the red emergency stop button to power it on.
  3. Open the red air valve: turn its handle down until it is parallel with the fitting.
  4. On the regulator, push the blue switch toward the regulator to let the air flow.
  5. Check the pressure gauge. It should read about 65 PSI.

Set the Temperature

Watch this part1:39
  1. On the touchscreen, tap the red temperature value.
  2. Enter the temperature you want on the number pad.
  3. Tap Back to save it.

Set the Press Times

Watch this part1:53
  1. Tap the clock icon. With Single Press selected, tap Setting.
  2. Enter your press time in seconds, then tap Back, and Back again.
  3. A single press is one cycle of heat and pressure. It is simple, but only ideal when the conditions and fabric allow it.
  4. For double press, tap the clock icon, select Double Press and tap Setting.
  5. Double press has two times, the pre-press time and the pressing time. Tap each one and enter the seconds.
  6. A double press adds a pre-press before the transfer is placed. It removes moisture and smooths the fabric. For most everyday garments, this is the recommended approach.
  7. Tap Back, and Back again.

Run a Double Press

Watch this part2:57
  1. The first press is the pre-press. Press both Press buttons, one on each side of the control box, to bring the head down. The head presses for the pre-press time.
  2. When it finishes, press the Swing button, or step on the foot pedal. The head swings over to the other side.
  3. Press both Press buttons again to begin the next cycle. There is a Press button on each side of the control box; on one side it sits below the Release button.
  4. If the cycle starts repeating unintentionally, press the Release button to stop it.
  5. Press the Swing button to swing the head back, then press both Press buttons again for the main press.
  6. When it is done, swing the head away.
  1. Tap the clock icon, select Triple Press and tap Setting.
  2. Triple press has three times. The third one is the re-pressing, or post-press, time.
  3. The post-press comes after the transfer is applied and peeled. With a cover sheet over the print, it seals the edges and evens out the finish.
  4. That makes it the best choice for textured fabrics, or any job where a durable, consistent result is critical.
  5. Tap Back.

Set the Pressure

Watch this part4:35
  1. Tap the pressure value, enter the pressure, then tap Back.
  2. The recommended pressure range is between 40 and 73 PSI.
  3. Below 40 PSI, the head may not move properly. At 30 PSI, the head does not move when you press the Swing button; at 40 PSI it swings normally.
  4. Above 73 PSI, the press can cause excessive force, damage or injury. Set it to 73 or lower.

Press Counter

Watch this part5:38
  1. Press Counting tracks how many presses have been completed. Each press adds one.
  2. To reset it, press and hold the number, then tap Counting Reset. The count goes back to zero.
  3. Tap Back.

Read the Status

Watch this part6:03
  1. The status, in the top right corner, shows what the machine is doing, for example Standby.
  2. When the head swings, it shows Swing Left, then Standby again.
  3. During a press, it shows Pressing, then Up as the head lifts. When the head comes down, it shows Down, then Pressing.
  4. If you press Release during a press, it shows Emergency On. Then it goes back to Standby.
  1. The Prisma Dual can save up to ten different presets, so you can quickly switch settings for different garments, fabrics or jobs.
  2. Tap Advanced Setting, then Preset Parameter. This screen holds the preset temperature, time and pressure.
  3. Tap Name Setting to see the ten preset slots. Tap the one you want, then tap Back. The screen now shows that slot's settings.
  4. Tap Name Setting again, then Preset Setting at the bottom.
  5. Type a name for the preset on the keyboard and tap Confirm. The new name is now in the slot. Tap Back.
  6. Tap the temperature value, enter the temperature and tap Back. Set the time and pressure the same way.
  7. Tap Back to go to the main menu.

Advanced Settings

Watch this part7:42
  1. Tap Temperature Calibration. Calibration is not needed in every setup. Use it if your temperatures are not reading accurately, or to work through an adhesion issue.
  2. Tap Start Calibrate. The light turns green while it calibrates, then orange again, back to standby. Tap Back.
  3. To change the temperature units, use Units Switch: tap Fahrenheit or Celsius.
  4. If you need to, Reset Setting at the top right resets all settings.
  5. For more help, tap Contact Support. Scan the QR code, or visit dtfstation.com, for operation, maintenance and tech support videos.
  1. Load your garment on the open platen and place your transfer on the garment.
  2. On the touchscreen, make sure Manual is selected.
  3. Press the Swing button, or use the foot pedal, to bring the head over the garment.
  4. Press both Press buttons to start the press. The press runs for the time you set.
  5. When it is done, swing the head away, then peel the film.

Semi-Auto Mode

Watch this part9:41
  1. Tap Semi-Auto. Load your garment on the open side, and position your transfer.
  2. In semi-auto mode, do not start with the Press buttons.
  3. Instead, press the Swing button, or the foot pedal, when you are ready. The head swings over, comes down, and completes the cycle on its own, based on your programmed time.
  4. While it presses, load the next garment on the open side and position the next transfer.
  5. When the cycle is done, press the Swing button to swing the head back. The second garment presses, and the first one is ready.
  6. Peel the film from the first garment. Swing the head back again, then peel the second transfer.
  1. Tap Auto.
  2. In auto mode, it is important to set the delay time. Tap Duration Setting. The duration is the pause between presses, before the head swings to the other side by itself.
  3. Enter the delay in seconds, then tap Back.
  4. Press both Press buttons to start the cycle. The head swings over, and presses on its own.
  5. You can load new garments while the press is cycling. The head alternates sides automatically, allowing continuous production.
  6. Once the head starts moving, it completes its motion. Always be aware of the machine during operation.
  7. To stop auto mode, press the Release button. The time counts down to zero, and the status shows Standby.
  8. The outer metal of the upper platen gets warm to the touch during operation, so handle the press with care.
  1. Start in semi-auto mode as you get familiar with the press, since it gives you more control.
  2. As you become more comfortable, auto mode is a great option for a steady workflow. Set the duration first.
  3. Before you start production, make sure all settings are correct, and that your mode matches your workflow.
  4. Monitor the temperature, pressure and timing regularly, and adjust them as needed.

Stuck on a step?

Our US tech team answers on Discord, and it is the fastest route to a person who knows this machine.

Get support