Miro 36 Pro

Miro 36 Pro Quick Start Guide

Every step links to its own moment in the videos, so you never hunt for the right part again.

  • 41 steps
  • 178 instructions
  • 4 videos
  • 4 chapters
  • Updated 2026-11-15
Resources1

1. Unbox and Set Up

How to Unbox and Set Up the Miro 36 Pro

  1. 0:00Tools and Safety
  2. 0:18Opening the Crate
  3. 1:12Removing the Dust Cover and Packing
  4. 2:03Spare Heating Lamp and Packed Parts
  5. 2:42Accessories Checklist
  6. 2:50Moving the Units off the Pallet
  7. 4:44Connecting the Cables
  8. 7:12Joining and Leveling the Units
  9. 8:07Installing the Tension Rods
  10. 10:37Installing the Cooling Fan
  11. 12:05Installing the Take-Up Reel
  12. 15:10Connecting the Take-Up Cables and Paper Core
  13. 16:05Lowering the Leveling Feet
  14. 16:30Connecting Power and Powering On
Written steps14

Tools and Safety

Watch this part0:00

What you need

  • At least two people for lifting
  • Power drill
  • Adjustable wrench
  • Gloves

Opening the Crate

Watch this part0:18
  1. Open each metal latch along the top edge: pull the lever out, then unhook the latch.
  2. Repeat for every latch around the top.
  3. With two people, lift the top panel straight up and set it aside.
  4. Open the latches down each corner and along the bottom edge.
  5. With two people, lift each side panel up and away.

Removing the Dust Cover and Packing

Watch this part1:12
  1. Lift off the black dust cover.
  2. Remove the foam blocks from the corners of the machine.
  3. Pull out the foam-wrapped pieces from under the machine. The dehumidifier can be thrown away.
  4. Unwrap the foam from the wooden board inside.
  5. Lay the wooden slat vertically beside the pallet, as shown in the video. It supports the ramp.

Spare Heating Lamp and Packed Parts

Watch this part2:03
  1. Lift the cover of the powdering unit.
  2. A replacement heating lamp is packed in tube number 3. With two people, remove it gently to avoid damage.
  3. Lift out the rest of the packed parts, then close the lid.
  4. Open the cabinet door below the Miro 36 Pro logo, take out the foam boxes and the cardboard box, then close the door.

Accessories Checklist

Watch this part2:42
  1. Lay out all of the accessories.
  2. Each part is numbered from 1 to 10. Check that nothing is missing.

Moving the Units off the Pallet

Watch this part2:50
  1. Lay one crate panel from the edge of the pallet down to the floor to make a ramp.
  2. Each leveling foot is held to the pallet by a metal bracket. Use the power drill to remove the bracket screws, then lift the bracket away.
  3. Remove every bracket around the machine.
  4. Raise the leveling feet so the machine sits on its wheels: use the wrench to move the nut above the foot down, then turn the foot pad to raise it.
  5. Repeat for every foot.
  6. Do not tilt the machine when unloading. With two people holding the top edges, slowly lower the powdering unit down the ramp.
  7. Lower the oven unit down the ramp the same way.

Connecting the Cables

Watch this part4:44
  1. Roll the two units close together.
  2. On the side of the oven unit, take the plastic wrap off each cable.
  3. Feed the first cable through its opening, push the plug onto its socket and turn the metal collar until it is tight.
  4. Connect the other two cables the same way.
  5. Open the dust cap on each numbered socket.
  6. Each cable comes through a numbered opening. Plug each cable into the socket with the matching number and turn the collar to lock it.

Joining and Leveling the Units

Watch this part7:12
  1. Find the two knobs on the side of the powdering unit. Turn the upper knob, then the lower knob, as shown in the video.
  2. With two people, push the units together, tucking the cables inside the gap, until the two units meet.
  3. Make sure the front and back are level on both sides. Run your hand across the seam to check.
  4. Turn the two knobs at the front seam, one near the top and one near the bottom.

Installing the Tension Rods

Watch this part8:07
  1. Move to the back of the machine. You need part 9 and part 7: two metal rods and four brackets.
  2. Place a bracket at an upper corner, at the circled point, and thread in its thumb screws by hand. Tighten them until the bracket is firm.
  3. Do the same on the other side.
  4. Hold one rod between the two upper brackets. Unscrew the black knob from the end of the rod and remove the bearing.
  5. Fit the rod end into the bracket, put the bearing back on, and tighten the knob. Do the same at the other end.
  6. Install the two lower brackets the same way, then fit the second rod between them and tighten the knobs.

Installing the Cooling Fan

Watch this part10:37
  1. You need part 8 and the parts in bag 7.
  2. Place a fan bracket at the circled point on the side of the machine, hold it flat and tighten its thumb screws.
  3. Mount the second bracket on the other side.
  4. Lift the cooling fan onto the brackets with its power cable on the side shown in the video.
  5. Remove the knobs, align the holes and tighten the first knob.
  6. Insert the second knob, set the fan to the angle you want, then tighten it. Repeat on the other side.

Installing the Take-Up Reel

Watch this part12:05
  1. You need parts 1, 4 and 9.
  2. Hold a take-up arm against the bottom of the cabinet and tighten its thumb screws, then the two additional thumb screws on the inside of the bracket.
  3. Mount the second arm on the other side the same way.
  4. On each arm, loosen the thumb screws above and below the holes.
  5. Slide one rod through a set of holes in both arms, then slide the second rod through the other holes.
  6. Take a take-up unit (part 4) and slide it onto the front rod. The second rod slides in horizontally.
  7. Do the same with the second half of the take-up reel.
  8. Place the final rod through the hole in the side bracket, then tighten all the knobs to secure the rods.

Connecting the Take-Up Cables and Paper Core

Watch this part15:10
  1. Connect the take-up cables to the sockets on the side: push each plug into its socket and turn the collar to lock it.
  2. Fit paper core 3 between the two take-up units.
  3. Tighten the knobs to hold the core in position.

Lowering the Leveling Feet

Watch this part16:05
  1. With the machine in place, turn each foot pad down until it rests on the floor.
  2. Turn the nut up against the machine to lock the foot.
  3. Do this for every foot.

Connecting Power and Powering On

Watch this part16:30
  1. Find the two power sockets. US machines run on 110V; outside the US, 220V.
  2. Plug one power cord (part 10) into the upper socket and the other into the lower socket.
  3. Plug each cord directly into its own wall outlet, with the two outlets on separate circuits (at 110V, a 20A circuit for each cord). Never plug both cords into the same circuit, a power strip or an extension cord.
  4. Press the upper power switch, then the lower power switch. Both light up, the DTF Station logo lights up and the touch screen turns on.
  5. To tilt the control panel out, press both bottom corners of its frame.
  • One power switch and outlet run the main heating element and the take-up reel. The other runs the IR lamps and the front heating element.

2. Operation and End-of-Day Maintenance

How to Operate and Maintain the Miro 36 Pro

  1. 0:11Before You Start
  2. 0:22Adjust the Front Heating Plate Height
  3. 1:47Line Up With the Printer
  4. 2:48Load the Film
  5. 4:29Film-Saving Loading
  6. 6:21Finish Film-Saving Loading
  7. 7:28Install the Media Wheel Bar
  8. 9:06Narrower Film (60 to 90 cm)
  9. 10:39Power On
  10. 11:10Set the Temperatures
  11. 11:49Start Printing
  12. 12:55End of Printing
  13. 14:40End-of-Day Shutdown
  14. 15:56Clean the Oven
  15. 17:49Filters and Drip Tray
  16. 19:24Clean the Powder Station
  17. 21:16Finish Up
Written steps17

Before You Start

Watch this part0:11
  1. Pull the dust cover off the machine.
  2. The film runs from your printer straight into the Miro 36 Pro.

Adjust the Front Heating Plate Height

Watch this part0:22
  1. Adjust the height of the front heating plate to match your printer. Lift the front heating plate up from its folded position.
  2. Method one: hook the plate support into a different slot on the bracket. We recommend slot three.
  3. Method two: loosen the four screws on the support bracket with a screwdriver, slide the bracket to the height you need, then tighten all four screws.
  4. Lower the plate back onto its support.

Line Up With the Printer

Watch this part1:47
  1. Roll the Miro 36 Pro up to the printer.
  2. Feed some film out of the printer and lay it across the front heating plate.
  3. Check where the film meets the edge of the plate: when the height is right, the film lies flat on the plate.
  4. Use the ruler on the plate to center the Miro 36 Pro with the film.
  5. Turn each leveling foot down until it rests on the floor, so the machine stays in place.

Load the Film

Watch this part2:48
  1. On the printer's control panel, press the down arrow to feed the film out.
  2. With the powder station cover open, push the film down into the powder station, then into the oven chamber.
  3. Open the oven unit's cover: press the latch on the side to release it, then lift the cover by its handle.
  4. Pull the film across the main heating plate, then close the cover.
  5. At the back, pull the film down toward the take-up reel and pass it under the tension rod.
  6. Wrap the film around the paper core and tape it in place. Keep some tension on the film so it sits straight.
  7. The media guides keep the film straight: position them against each edge of the film. Then do the same on the lower rod.

Film-Saving Loading

Watch this part4:29
  1. Instead of pulling new film through the whole machine, you can use a leftover roll as a leader.
  2. Place a roll of leftover film on the take-up reel. Open the powder station cover and the oven unit's cover.
  3. Pull the leftover film up over the back of the oven, routing it under the tension rod.
  4. Lay it across the main heating plate, let it drop into the powder station, then pull it through the powder station toward the front and over the front heating plate.
  5. Line up the edge of the leftover film with the edge of the new film from the printer, using the ruler.
  6. Join the two films with strips of tape across the seam, then add tape all along the joint. We recommend using heat tape for this method.
  7. Both edges should sit at the same mark on the ruler.

Finish Film-Saving Loading

Watch this part6:21
  1. At the take-up reel, take off the leftover roll.
  2. Put an empty paper core on the take-up reel and fit its end into the motor holder.
  3. Pull the film down and tape it to the core.
  4. Close the oven cover over the film, place the media wheel rod on the film in the powder station, and close the powder station cover.
  5. The film runs under the tension rod and lies flat on the front heating plate.
  6. Put on gloves before you work near the hot oven, then guide the film down to the take-up reel.

Install the Media Wheel Bar

Watch this part7:28
  1. You need the rod and the white media wheels.
  2. Slide a wheel onto the rod and tighten its set screw with a screwdriver.
  3. For 90 centimeter film: lower the rod into the powder station, slide the wheel to the edge of the film using the ruler, and tighten its set screw.
  4. Set the wheel at the other end close to the media sensor, and tighten its set screw. The sensor's light shows that it can detect the wheel.

Narrower Film (60 to 90 cm)

Watch this part9:06
  1. Loosen the set screw on the wheel and put the rod back on the film.
  2. Slide the wheel to the edge of your narrower film using the ruler, then tighten its set screw.
  3. Add an extra wheel about ten centimeters from the end of the rod and tighten its set screw.
  4. Put the rod back in the powder station. The extra wheel sits next to the media sensor, so the sensor can still detect it with narrower film. The other wheel sits on the edge of the film; adjust it with the screwdriver if you need to.
  5. Pour powder along the film, between the wheels.
  1. Plug the first power cord into an outlet, then plug in the second power cord. Make sure it goes to a separate breaker.
  2. At the back, plug one power cord into the upper socket and the other into the lower socket.
  3. Press the upper power switch, then the lower power switch. Both light up.
  4. To tilt the control panel out, press the bottom edge of its frame.

Set the Temperatures

Watch this part11:10
  1. Tap Adjust Temp to see the four heating zones.
  2. The defaults are 176°F (80°C) for the front heating plate, 266°F (130°C) for the main heating plate and 167°F (75°C) for the heating tube.
  3. To change a temperature, tap its zone, type the new temperature on the keypad, then tap Confirm.
  4. Tap the back arrow to return to the main screen.

Start Printing

Watch this part11:49
  1. Turn on the take-up reel with the switch on the take-up motor.
  2. Print a nozzle check first, and make sure every nozzle fires. Then start printing.
  3. Pause the printer before the first print enters the powdering station.
  4. On the Miro 36 Pro screen, tap the paddle speed button to turn the paddle on, and tap plus to raise the speed.
  5. Tap Fume Extractor to turn it on. Its intensity knob is inside the cabinet door: turn it counterclockwise to decrease the intensity, clockwise to increase it.

End of Printing

Watch this part12:55
  1. When printing is finished, press the button on the printer's keypad that feeds the film forward (shown in the video), so the film moves past the front heating plate.
  2. Lift the end of the film off the front heating plate and feed it into the powder station by hand, a little at a time: move it forward once every five seconds.
  3. Turn off the take-up reel. Let the last part of the film stay in the oven for about three to five minutes.
  4. On the screen, tap the paddle speed button to turn the paddle off.
  5. Turn the take-up reel back on and hold the film gently while the reel winds it in. Then turn off the take-up reel and take the finished roll off.

End-of-Day Shutdown

Watch this part14:40
  1. You need a clean cloth and gloves.
  2. Turn off all the heaters: tap each heating zone, enter zero, and tap Confirm. Do this for all four zones.
  3. Leave the fume extractor on. Open the powder station cover and the oven cover, and let the Miro 36 Pro cool for ten to twenty minutes.
  4. Keep the fume extractor running for ten minutes to clear all the smoke out of the machine, then tap Fume Extractor to turn it off.
  5. Press the upper power switch, then the lower power switch, to turn them off. Unplug both power cords at the back.

Clean the Oven

Watch this part15:56
  1. Wipe the inside of the oven cover around the heating lamps with the cloth. Don't wipe the heating lamps themselves: a broken lamp can cut your fingers.
  2. Spray cleaning solution onto the cloth and wipe the whole main heating plate, edge to edge.
  3. Brush any powder out of the back corners and along the back edge.
  4. Close the oven cover and press the latch to lock it.

Filters and Drip Tray

Watch this part17:49
  1. Open the cabinet door. Pull out the top filter by its strap, then the filter below it.
  2. Don't wash the cold catalyst filter or the activated carbon filter. Let both air-dry in a cool, dry, shaded place, and only put them back when they're completely dry.
  3. Wipe out the filter compartment with the cloth.
  4. When the filters are dry, slide the activated carbon filter into the bottom slot, then the cold catalyst filter into the top slot. Raise the seal to create space.
  5. After work, open the drain valve and leave it open overnight.
  6. Pull out the drip tray below it, clean it out with a cloth dampened with isopropyl alcohol, and slide it back in. Close the cabinet door.

Clean the Powder Station

Watch this part19:24
  1. Open the powder station cover and lift out the media wheel rod. Brush the powder off the wheels.
  2. Brush the powder out of the powder station, and gently wipe the media sensor with the cloth.
  3. Pull out the powder tray, then remove the second tray.
  4. Brush the floor of the powder station again, then brush the powder off the ledge into a tray held under it.
  5. Slide the trays back in after disposing of the waste powder.
  1. Put the media wheel rod back in the powder station: the two wheels at one end sit next to the media sensor, then set the wheel at the other end.
  2. Close the powder station cover.
  3. Wipe the front heating plate, then fold it down.
  4. Wipe down the top of the machine, and cover the Miro 36 Pro with its dust cover.

3. Update the PLC Program

How to Update the PLC Program on the Miro 36 Pro

  1. 0:09Power Off and Open the Electrical Box
  2. 0:24Slide Out the Electrical Tray
  3. 0:46Power On
  4. 0:56Connect Your Laptop
  5. 1:19Run the Update
  6. 1:53Put It Back Together
Written steps6

Power Off and Open the Electrical Box

Watch this part0:09
  1. Turn off the shaker at the power switch.
  2. To be safe, unplug the power cable too.
  3. Remove the 10 screws around the electrical box panel and take the panel off.

Slide Out the Electrical Tray

Watch this part0:24
  1. Behind the panel, 4 nuts hold the electrical tray in place. Remove all 4.
  2. Slide the tray out slowly, and watch the cables on top so they don't get scratched.
  3. A gentle wiggle helps it come free.
  1. Plug the power cable back in and turn the power on.
  2. Wait for the touchscreen to finish starting up.

Connect Your Laptop

Watch this part0:56
  1. Use a good quality USB cable with a Type-C plug on one end. The other end goes to your laptop, so pick a plug that fits it.
  2. Find the Type-C socket on the PLC board and plug the cable in.
  3. Connect the other end to your laptop.

Run the Update

Watch this part1:19
  1. On the laptop, find the updated Miro 36 Pro program file and open it.
  2. In the window that opens, check the COM port. If your laptop lists more than one, unplug the USB cable and plug it back in: the port that disappears and comes back is your Miro.
  3. Select that port and click Download.
  4. A progress bar shows the update running. Wait for it to finish.
  5. When it is complete, click OK, then close.

Put It Back Together

Watch this part1:53
  1. Unplug the USB cable.
  2. Turn the power off again before you put everything back, and unplug the power cable.
  3. Slide the tray back in, again watching the cables.
  4. Secure the tray at all four corners.
  5. Reinstall the panel.

4. Update the Screen UI

How to Update the Screen UI on the Miro 36 Pro

  1. 0:09Remove the Screen
  2. 0:25Insert the SD Card
  3. 0:50Run the Update
  4. 1:06After the Update
Written steps4

Remove the Screen

Watch this part0:09
  1. The screen is held in place by four screws.
  2. Before you take them out, turn off the power switch, then unplug the power cord.
  3. Remove the four screws and lift the screen out of its frame.

Insert the SD Card

Watch this part0:25
  1. Turn the screen over to the circuit board on the back and find the micro SD card slot.
  2. You need a micro SD card with the update file on it. Use a 16 or 32 GB card only: larger cards won't be recognized by the screen.
  3. Insert the card into the slot and make sure it is pushed all the way in.

Run the Update

Watch this part0:50
  1. Plug the power cord back in and turn the shaker on.
  2. When the screen starts up, it shows the SD card upgrade menu. Tap Upgrade HMI Data, the middle button.
  3. The update starts. Don't cut the power while it runs.

After the Update

Watch this part1:06
  1. If you need the update file, DTF Station can send it preloaded on a card, or you can download it.
  2. Remove the SD card. You can reuse it on other units.

Stuck on a step?

Our US tech team answers on Discord, and it is the fastest route to a person who knows this machine.

Get support