Introduction and Purpose
Watch this part0:02- Watch the full setup video series step by step to ensure proper installation and minimize downtime.
- Pause or rewind videos as needed to follow instructions accurately.
Miro 13 Max
Miro 13 Max Quick Start Guide
Every step links to its own moment in the videos, so you never hunt for the right part again.
User manualThe full manual, beyond first setup. · All manuals
Quick Start Guide
Quick Start Guide Access - Videos, Software, and Documents
- 0:02Introduction and Purpose
- 0:36Alternative Access via Email
- 1:26Using and Storing the Quick Start Guide
Written steps6
Locating the Quick Start Guide via USB
- Locate the USB drive included with your printer.
- Insert the USB drive into your computer.
- Open the Quick Start Guide PDF file stored on the USB.
Alternative Access via Email
Watch this part0:36- If the USB drive is missing or its contents are unavailable, open the email from the dealer where the printer was purchased.
- Locate the most up-to-date Quick Start Guide URL link provided in the email.
- Double-click the Quick Start Guide PDF file from the link.
Downloading and Saving the Quick Start Guide
- Open the Quick Start Guide PDF.
- Click on Important Resources.
- Download the Quick Start Guide PDF.
- Save a copy of the PDF to your desktop.
Using and Storing the Quick Start Guide
Watch this part1:26What you need
- One-page PDF format
- Contains QR codes
- Includes links to videos, software, and documents needed for setup
- Stored in an easily accessible location
Next Steps
What you need
- Proceed to the next setup video
Assembly
Miro 13 Max Powder Shaker Oven - Installation Guide
- 0:02Tools and Unboxing Preparation
- 1:05Initial Unit Preparation
- 1:48Bracket Assembly
- 3:34Film Tension Rod Installation
- 4:59Takeup Motor Connection
- 5:39Power Connection and Initial Power-On
- 6:04Functional Testing
- 6:36Temperature Settings and Film Notes
- 7:09Shutdown and Table Installation
Written steps11
Tools and Unboxing Preparation
Watch this part0:02What you need
- Screwdriver
- Work gloves
- Blade
- Open the box using a blade.
- Remove all items from inside the box.
- Remove and set aside all styrofoam packaging.
- Note that contents may change over time and contact DTF Station technicians if there are significant differences from the video.
Initial Unit Preparation
Watch this part1:05- Open the powder station lid.
- Remove the takeup reels and takeup reel brackets.
- Close the powder station lid.
- With at least two to three people, carefully lift and remove the unit from the box.
- Locate the rods underneath the Miro 13 Max.
- Remove protective films from all accessories.
- Place the styrofoam back into the box and retain it for future use.
- Retain all original packaging, including styrofoam, for warranty purposes for up to six months.
- Take a photo of the serial number sticker.
- Register the equipment on the Discord profile page using the serial number.
Bracket Assembly
Watch this part1:48- Locate the two brackets shown in the video.
- Find the knob screws in the Ziploc bag.
- Connect the brackets using three knob screws on each side.
Film Tension Rod Installation
Watch this part3:34- Locate the silver film tension rod.
- Insert the rod into the brackets using two bearings and knob screws.
- Insert the film alignment adjusting ring before locking the rod.
- Insert the knob screws on both sides.
- Adjust the rod until it is straight.
- Tighten the knob screws securely.
Takeup Reel Rod Installation
- Thread the two takeup reel rods into the brackets.
- Partially loosen the knobs on the takeup reels.
- Insert the takeup reels into the rods.
- Loosen the knobs on the brackets to center the rods.
- Once centered, tighten all knobs.
- Spread out the takeup reels.
- Insert the paper core onto the takeup reel.
- Center the paper core.
- Tighten the knob screw to secure the paper core.
Takeup Motor Connection
Watch this part4:59- Connect the takeup motor connector to the Miro 13 Max body.
- Ensure the connector is fully and properly seated.
Media Wheel Assembly
- Locate the media wheel components.
- Loosen the screws to insert the rods.
- Partially lock the rods in place.
- Do not overtighten to avoid bending the rods.
- Open the powder station lid.
- Place the media wheel into the groove inside the powder station.
Power Connection and Initial Power-On
Watch this part5:39- Locate the power cord.
- Plug the power cord into the unit.
- Plug the other end into a power source using a power strip to prevent sudden power loss.
- Turn on the main power.
- Verify that the display turns on.
Functional Testing
Watch this part6:04- Turn on the preheating button.
- Wait approximately 5 minutes.
- Verify the preheating platen is warming up.
- Turn on the purifier.
- Confirm the purifier fan is running.
- Turn on the shaking power.
- Adjust the shaking speed intensity control knob to increase or decrease paddle speed.
- Turn on the takeup reel power.
- Verify the takeup motor runs when the media wheel is engaged.
Temperature Settings and Film Notes
Watch this part6:36What you need
- Main heating plate default temperature: 130 C
- Preheating plate temperature range: 50 to 80 C
- Color Prime Universal Film: warm peel film
- Color Prime Quick Glide Film: hot peel film
- Refer to the operation video for correct film settings
- Contact a DTF Station technician if assistance is needed
- Press the reset button to set default temperatures.
Shutdown and Table Installation
Watch this part7:09What you need
- Print Pro table is sold separately
- Contact a local distributor to purchase the table
- Refer to the Print Pro table installation video for table setup
- Turn off the main power.
- Unplug the power cord.
- Allow the unit to cool for several minutes.
- Move the unit onto the Print Pro table.
- Position the wheels with brakes facing outward to align with the table slots.
- Engage the brakes on all four wheels.
Stuck on a step?
Our US tech team answers on Discord, and it is the fastest route to a person who knows this machine.