See what's new at PRINTING UnitedNew at PRINTING UnitedBooth 3268 · Las Vegas · Sept 23–25Book a demo
ContactShop — dealer and account ordering

Seismo L16R & L24R

Seismo L16R & L24R - Maintenance Guide

Every step links to its own moment in the video, so you never hunt for the right part again.

  • 9 steps
  • 44 instructions
  • 1 video
  • Updated 2026-02-17

Seismo L16R User manualSeismo L24R User manualThe full manual, beyond first setup. · All manuals

Seismo L16R and Seismo L24R Maintenance and End-of-Day Cleaning Guide

  1. 0:00Feeding Out Final Media
  2. 0:23Shutting Down Heat and Powder Systems
  3. 0:38Final Film Feeding and Powdering
  4. 1:18Final Curing and Take-Up Control
  5. 1:56Full System Shutdown
  6. 2:33External Powder Cleanup and Vent Cleaning
  7. 3:18Cooling and Internal Cleaning
  8. 3:45Weekly or As-Needed Sensor and Glycerin Maintenance
Written steps9

Feeding Out Final Media

Watch this part0:00
  1. Turn on the vacuum function.
  2. Feed out an additional foot of media.
  3. Press the down arrow key for 2 seconds.
  4. Wait 5 seconds.
  5. Repeat until enough film is fed out to ensure final prints cure properly.

Shutting Down Heat and Powder Systems

Watch this part0:23
  1. Turn off the front heating plate.
  2. Turn off the powder recirculation.
  3. Cut the media while pulling slightly to prevent crinkling.

Final Film Feeding and Powdering

Watch this part0:38
  1. Manually feed the remaining film into the shaker.
  2. Slowly open the center lid.
  3. Hold the film from the center opening to maintain control.
  4. Wait until the last print is fully powdered before releasing the film.

Final Curing and Take-Up Control

Watch this part1:18
  1. Set the shaker to Manual mode.
  2. Monitor curing as the last print passes through the shaking zone.
  3. Turn off the shaking function once the last print exits the conveyor belt area.
  4. Apply tension to the film to slow the take-up reel.
  5. Prevent the film from rolling up too quickly.

Full System Shutdown

Watch this part1:56
  1. Turn off the take-up system.
  2. Turn off the main heat.
  3. Turn off the sub heat.
  4. Turn off the vacuum.
  5. Turn off the conveyor.

Powder Recovery and Cleaning

  1. Turn on the vacuum function to pull powder from the bottom to the top powder station.
  2. Brush off excess powder.
  3. Place the end-of-day tray over the vacuum area.
  4. Press and hold the cleaning button for more than 5 seconds to expel remaining powder.
  5. Use the provided spatula to tap inside the powdering station.
  6. Brush powder into the tray.
  7. Pour recovered powder into a sealed container with desiccant.

External Powder Cleanup and Vent Cleaning

Watch this part2:33
  1. Vacuum remaining powder around the machine.
  2. Leave the air purifier running for at least 5 minutes before disconnecting.
  3. Clean the inside of the oven vent using a lint-free cloth and isopropyl alcohol.

Cooling and Internal Cleaning

Watch this part3:18
  1. Unlatch the heating elements.
  2. Fully open all lids.
  3. Allow the machine to cool for at least 10 minutes.
  4. Remove excess powder or glycerin buildup.
  5. Clean all residue using isopropyl alcohol.
  6. Close and latch the oven area.

Weekly or As-Needed Sensor and Glycerin Maintenance

Watch this part3:45
  1. Clean the sensor using a lint-free cloth and isopropyl alcohol.
  2. Keep all covers closed to prevent dust and debris accumulation.
  3. Use a Phillips screwdriver to remove the screw from the glycerin container.
  4. Inspect glycerin buildup inside the container.
  5. Clean the container using isopropyl alcohol.
  6. Reinstall and secure the screw.

Stuck on a step?

Our US tech team answers on Discord, and it is the fastest route to a person who knows this machine.

Get support