Prestige R1 - Operation Guide

1. Safety Tips

Air Filtration & Maintenance (00:00–00:30)Phoenix Air, L2 Purifier, and Miro 13 all use:

DTF Station — General Safety & Best PracticesPurposeFollow these guidelines to maintain equipment performance, protect your workspace, and ensure user safety throughout daily DTF operations. HEPA filter Charcoal filter Filters should be replaced monthly. This maintenance applies even if your machine has a built-in purifier. Ventilation Recommendations (00:00–00:45)Always use additional ventilation, even with built-in purification. Recommended practices: Open a window Use a fan Ensure airflow around the equipment Especially important for home-based setups. Powder Handling & End-of-Day Safety (00:00–01:02)Always return unused powder back into its bag after printing. Reasons: Maintains powder quality and longevity Reduces airborne exposure Improves overall user safety Treat powder handling as a mandatory safety step, not optional. Personal Protective Equipment (PPE) (01:02–End)Recommended additional safety precautions: Gloves Protective eyewear Face mask (optional but encouraged) DTF Station tests all inks and powders for safety, but PPE adds another layer of protection. Support & Safety DocumentationContact your local dealer for: Material Safety Data Sheets (MSDS) Ink and powder safety documentation Additional handling guidelines Key ReminderDTF Station prioritizes both performance and safety. Safe operation protects you, your workspace, and your equipment long-term.

2. Beginning of Day Procedure

1. 0:00Power On & Initial Checks
2. 1:05Waste Ink Bottle Inspection & Disposal
3. 1:49Fill Ink Procedure
4. 2:35Head Cleaning Procedure

Prestige R1 — Daily Maintenance (Before Printing)PurposeComplete these steps before starting any print job to ensure ink flow, print head health, and consistent print quality.

3. Pilot Software Basics

Suction (Printer Bed Vacuum) (00:00–00:45)Off

DTF Station Pilot — Settings Overview & RecommendationsPurposeUnderstand each setting in DTF Station Pilot, what it controls, and DTF Station’s recommended defaults for performance, quality, and speed. Vacuum activates only when the print head carriage moves onto the media Recommended setting Open Vacuum runs continuously Controls how the media is held flat on the printer bed General Settings — Print Speed & Direction (00:00:45–01:10)Print Speed Low → slowest, highest control Middle → best print quality High → fastest print speed (recommended for most jobs) Print Direction Bidirectional (BiDirect) Prints left and right Fastest option Left Only / Right Only Prints on a single pass Slower but increases accuracy and sharpness Pre-Flashing (01:10–01:40)Open (recommended) Printer spits a small amount of ink into the capping station before printing Ensures proper ink firing Close Disables pre-flashing Auto Clean Options (01:40–02:10)Close (current default) Available cleaning options: Clean Flush – quick pre-flash into capping station Clean Weak – same as pressing the regular cleaning button Clean Normal – longer dwell time with increased pump pressure Clean Strong – longest dwell time and highest pressure Automatic behavior: Printer stops after 10,000 passes to perform a cleaning automatically Carriage Margin Settings (02:10–02:55)Type: Together (recommended) Print head only travels the width of the actual image Faster printing for small graphics Type: Off Print head travels full media width regardless of image size Slower printing Auto Reset: Yes (recommended) Resets travel width for each new image Prevents slowdowns when switching between different image sizes Media Settings (02:55–03:18)Print Start Position Example shown: 50 mm Value depends on how the media is loaded Measure distance from carriage home position to media edge Confidence Strip Settings (03:18–04:22)Purpose: Prints a small ink strip on the media edge Prevents CMYK inks from drying during long white-only prints Mode Options Wedding Status Wedding & Status Recommendation Minimum: Wedding Best quality: Wedding & Status Position Closest to home position (right side) — recommended Opposite side increases carriage travel Both sides further slows printing Strength Weak Normal (recommended) Strong (more ink flow) Width Example: 3 mm Adjustable thinner or thicker Distance from print Recommended: ≥ 1 mm Too close → difficult trimming Too far → wasted media Print Overlap Settings (04:22–05:27)Mode Light → fastest, everyday production Normal → higher resolution Depth → higher resolution than normal Super Eclosion → highest resolution, slowest speed Type Fog Type → prioritizes speed Strong A → prioritizes quality Ink Charge (05:27–05:55)Used for: First-time ink filling Resolving clogging Long idle periods Behavior: Capping station lifts Ink pumps into waste bottle Can be used for: Initial setup Periodic maintenance Print Settings (05:55–06:37)Print Mode CW (Color + White) — recommended 4C — color only Color Control Normal — recommended Color — color inks only White — white ink only Ink to Deepen (06:37–07:05)Default: Off Modes: Mode 1 → slightly darker Mode 2 → darker Mode 3 → darkest Does not affect print speed Useful when prints appear lighter than expected Mirror Print (07:05–07:20)Typically handled in DigiRip Option available for horizontal mirroring if needed Global Ink Setting & Spot Color (07:20–End)Global Ink Setting Allows doubling ink output Commonly used to double white ink Significantly reduces print speed Example impact: Normal speed: ~0.9 m/hr Double white: ~0.3–0.4 m/hr Recommended use: Disable unless specifically needed Spot Color Not currently utilized If enabled, uncheck and save Key TakeawayMost production slowdowns are caused by Single-direction printing High overlap modes Global ink doubling DTF Station’s recommended defaults balance speed, quality, and reliability for daily production.

4. Basic Operation ft. Phoenix Oven

1. 0:00Pre-Print Checks & Nozzle Verification
2. 0:45Film Advance & Speed Settings
3. 1:46Job Setup in NeoStampa
4. 3:21Nesting & Sending the Print Job
5. 4:28Monitoring the Print Queue & Oven Prep
6. 5:52Cutting, Powdering & Pre-Heating
7. 6:52Curing the Print
8. 7:40Heat Press Setup & Garment Prep
9. 8:40Pressing the Transfer

Prestige R1 — Basic Operation Overview (Printing to Curing & Pressing)PurposeWalk through the end-to-end DTF workflow using the Prestige R1 with Fenix Air Oven, from pre-print checks through curing and heat pressing.

5. A Deep Dive into NeoStampa

NeoStampa — Advanced Capabilities Deep DivePurpose

Understand how to create, manage, modify, and optimize print jobs in NeoStampa, including file handling, white ink control, color adjustments, and color matching. Section 1: Importing, Modifying & Saving Jobs (00:00–03:17) Creating Jobs & Importing Images Click New Job. Select your printer and scheme. Example: Prestige R1 with 720 × 440 scheme. Import images using any of the following methods: Click Add File Drag and drop an image from the desktop Click Open Job Observe that each import method may create a new tab, representing separate jobs or batches. Modifying a Job Resize images as needed. Duplicate images if required. Click Nest. Set nesting margin to 0.25 in to allow cutting space. Saving Job Files Click File → Save. Save the job as a CPS file. CPS files: Open in NeoStampa Remain fully editable Ideal for reprints and reorders Close the job tab. Printing & PRT Files Modify the second batch as needed. Click Print instead of Save. This creates a PRT file. PRT files: Open only in DTF Station Pilot Cannot be reopened in NeoStampa Wait for processing to finish before moving or using the PRT file. Always confirm the correct scheme when reopening CPS files. CPS = editable NeoStampa job file PRT = print-ready file used by Pilot Section 2: Adjusting White Ink Amount & Choke (03:17–05:42) Method 1: Adjusting Individual Images Select an image. On the right panel, click White Effect Layer. Under Flat Method, adjust Intensity (%). Example: Reduce to 70% if too much white ink is present. Click Save. Method 2: Adjusting via Profile Settings Click the three-dot icon in the upper-right corner. Select the correct profile next to Five Color. Click the White Ink icon. Adjust the Intensity (%). Click OK. Adjusting Choke In the same menu, locate Choke. Right-click to change units to mm. Enter the desired choke value. Example: 1 mm to reduce white edge pickup. Click OK → Save. Confirm saving when prompted to apply changes to all images. Section 3: Adjusting Colors (05:42–06:52) Per-Image Color Adjustments Select an image. Click Color Adjustments (upper-right panel). Adjust: Brightness Contrast Saturation Preview changes. Click Apply. Adjustments apply one image at a time. Batch adjustment is possible but not recommended for accuracy. Making Adjustments Global Click the three-dot icon. Select Advanced. Click Input Defaults. Enable color adjustment options. Adjust values as needed. Click OK → Save → Yes. All future images will now inherit these adjustments. Section 4: Color Matching & Replacement (06:52–End) Manual Color Replacement Select the image. Click the Color Replacement tool. Click the target color in the image. Review the existing RGB values. Adjust RGB values as desired. Example: Change R value to 255. Click OK. NeoStampa will now replace this RGB value whenever it appears. Color replacement can be deleted if it affects gradients or unintended colors. Using a Color Chart for Accuracy Open the Color Replacement tool again. Select the target color. Click Variations. Adjust: Deviation Step count (example: 8 for larger charts) Patch size Click OK to generate the color chart. Rotate and prepare the chart for printing. Click Nest → OK. Print the chart. Identify the preferred RGB value. Update your artwork accordingly.