Prestige L2 & XL2 - Prestige Large Format - How to Replace White Ink Diverter

Prestige L2 & XL2

Prestige L2 & XL2 - Prestige Large Format - How to Replace White Ink Diverter

Every step links to its own moment in the video, so you never hunt for the right part again.

10 steps
60 instructions
1 video
Updated 2026-04-20

Prestige L2 User manual Prestige XL2 Installation & setup guideThe full manual, beyond first setup. · All manuals

How to Replace the Ink Diverter on Prestige L2 / XL2 / XL2 Pro / XL3 / XL4

Written steps10

Overview and Applicability

Watch this part0:00

Confirm this procedure applies to Prestige L2, XL2, XL2 Pro, XL3, and XL4 printers.
Ensure the printer is powered on before beginning.

Preparing the Printer

Go to the back of the printer.
Close the white ink line as shown.
Remove four screws from the top of the front cover.
Fully open the front cover.
Press and hold the left arrow key until the carriage moves to the center of the printer bed.
Turn the printer off.

Removing the Carriage and Daughterboard Covers

Watch this part0:42

Remove two screws from each side of the carriage cover.
Remove the carriage cover.
Loosen two screws from each side of the daughterboard cover.
Remove the daughterboard cover.

Disconnecting the Daughterboard

Watch this part1:32

Identify the ink diverter.
Cut and remove the zip tie using scissors.
Cut all white ink tubes above the white dampers.
Remove four screws securing the daughterboard.
Take photos of all cables on the daughterboard for reference.
Disconnect the cables from the daughterboard.
Carefully pull the daughterboard away from the carriage.
Place the daughterboard to the side without pulling on ribbon cables.

Removing the Ink Diverter Assembly

Watch this part2:19

Remove four screws securing the base plate.
Remove the base plate.
Locate and remove two screws near the ink diverter.
Slide the zip tie upward to release it.
Slide the bracket away from the ink diverter to create working space.
Place paper towels underneath the diverter.

Removing Ink Tubes From the Diverter

Watch this part2:54

Use scissors to loosen the W2 ink tube from the diverter.
Pull the W2 tube off by hand.
Loosen the W1 tube.
Plug the open nozzle with your finger before removing the second tube.
Prepare a cup or bowl.
Remove the second tube.
Position the diverter over the cup or bowl.
Release the nozzle to fully drain the diverter.
Repeat this technique to remove all remaining white ink tubes.

Installing the New Ink Diverter

Watch this part3:41

Bring the new ink diverter into position.
Begin reconnecting the ink tubes.
If a tube feels loose, cut the end straight across for a snug fit.
If a tube is difficult to install, soak the tube end in hot water for a few minutes.
Connect the W1 tube to the left side of the diverter.
Connect the W2 tube to the right side of the diverter.
Remove paper towels and clean any spilled ink.

Securing the Diverter and Reassembly

Watch this part4:22

Secure the diverter to the bracket using a zip tie or packing tape.
Secure the bracket using two screws.
Slide the zip tie back to its original position.
Route cables through the opening on the base plate.
Secure the base plate using four screws.

Reinstalling the Daughterboard and Covers

Watch this part5:13

Bring the daughterboard back to the carriage.
Reconnect all cables using the reference photos.
For the two identical cables, connect: Cable labeled 1 to the top port
Secure the daughterboard with four screws.
Reinstall the daughterboard cover.
Tighten four screws.
Unclip all white ink tubes from the front.
Go to the back of the printer and release the white ink line.
Reinstall the carriage cover.
Secure the carriage cover with four screws.

Cable labeled 2 to the bottom port

Power On and Verification

Turn the printer back on.
Verify the printer initializes correctly.
Confirm the printer status shows idle.

Stuck on a step?

Our US tech team answers on Discord, and it is the fastest route to a person who knows this machine.